404 lines
9.8 KiB
INI
404 lines
9.8 KiB
INI
|
# This file allows user to override the factory
|
||
|
|
|
||
|
|
# defaults for the WLAN Driver
|
||
|
|
|
||
|
|
#Host module debug
|
||
|
|
vosTraceEnableHDD=0
|
||
|
|
vosTraceEnableWDA=0
|
||
|
|
vosTraceEnableWDI=0
|
||
|
|
vosTraceEnableSME=0
|
||
|
|
vosTraceEnablePE=0
|
||
|
|
vosTraceEnableWMA=0
|
||
|
|
vosTraceEnableVOSS=0
|
||
|
|
gEnableLogp=1
|
||
|
|
|
||
|
|
#Prioritize user(hostapd, iw,) specified country
|
||
|
|
gCountryCodePriority=1
|
||
|
|
|
||
|
|
#Host logging
|
||
|
|
gMulticastHostFwMsgs=0
|
||
|
|
|
||
|
|
#packetlog
|
||
|
|
gEnablePacketLog=0
|
||
|
|
|
||
|
|
#Enable firmware uart print
|
||
|
|
gEnablefwprint=0
|
||
|
|
|
||
|
|
#Enable firmware log
|
||
|
|
gEnablefwlog=0
|
||
|
|
|
||
|
|
# Disable FW log function by default
|
||
|
|
gFwDebugLogType=0
|
||
|
|
gFwDebugModuleLoglevel=0,0
|
||
|
|
|
||
|
|
# Generic
|
||
|
|
|
||
|
|
# Phy Mode (auto, b, g, n, etc)
|
||
|
|
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
|
||
|
|
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
|
||
|
|
# 7 = 11b only 8 = 11ac only.
|
||
|
|
gDot11Mode=0
|
||
|
|
|
||
|
|
# VHT Tx/Rx MCS values
|
||
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
||
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
||
|
|
gVhtRxMCS=2
|
||
|
|
gVhtTxMCS=2
|
||
|
|
|
||
|
|
# VHT Tx/Rx MCS values for 2x2
|
||
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
||
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
||
|
|
gEnable2x2=1
|
||
|
|
gVhtRxMCS2x2=2
|
||
|
|
gVhtTxMCS2x2=2
|
||
|
|
|
||
|
|
gVhtChannelWidth=2
|
||
|
|
|
||
|
|
#Short Guard Interval Enable/disable
|
||
|
|
gShortGI20Mhz=1
|
||
|
|
gShortGI40Mhz=1
|
||
|
|
|
||
|
|
#Channel Bonding
|
||
|
|
gChannelBondingMode5GHz=1
|
||
|
|
|
||
|
|
# 1=enable STBC; 0=disable STBC
|
||
|
|
gEnableRXSTBC=1
|
||
|
|
|
||
|
|
# 1=enable tx STBC; 0=disable
|
||
|
|
gEnableTXSTBC=1
|
||
|
|
|
||
|
|
# 1=enable rx LDPC; 0=disable
|
||
|
|
gEnableRXLDPC=1
|
||
|
|
|
||
|
|
#If set to 0, MCC is not allowed.
|
||
|
|
gEnableMCCMode=1
|
||
|
|
|
||
|
|
# Enable or Disable MCC Adaptive Scheduler at the FW
|
||
|
|
# 1=Enable (default), 0=Disable
|
||
|
|
gEnableMCCAdaptiveScheduler=1
|
||
|
|
|
||
|
|
# Enable BMPS or not
|
||
|
|
gEnableBmps=1
|
||
|
|
|
||
|
|
# Enable IMPS or not
|
||
|
|
gEnableImps=1
|
||
|
|
|
||
|
|
# Enable/Disable Idle Scan
|
||
|
|
gEnableIdleScan=0
|
||
|
|
|
||
|
|
#Data Inactivity Timeout when in powersave (in ms)
|
||
|
|
gDataInactivityTimeout=200
|
||
|
|
|
||
|
|
# Increase sleep duration (seconds) during IMPS
|
||
|
|
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
|
||
|
|
# unnecessary if Idle Scan is disabled.
|
||
|
|
gImpsModSleepTime=0
|
||
|
|
|
||
|
|
# Enable suspend or not
|
||
|
|
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
|
||
|
|
gEnableSuspend=3
|
||
|
|
|
||
|
|
|
||
|
|
#Enable/Disable UAPSD for SoftAP
|
||
|
|
gEnableApUapsd=1
|
||
|
|
|
||
|
|
# UAPSD service interval for VO,VI, BE, BK traffic
|
||
|
|
InfraUapsdVoSrvIntv=0
|
||
|
|
InfraUapsdViSrvIntv=0
|
||
|
|
InfraUapsdBeSrvIntv=0
|
||
|
|
InfraUapsdBkSrvIntv=0
|
||
|
|
|
||
|
|
# Flag to allow STA send AddTspec even when ACM is Off
|
||
|
|
gAddTSWhenACMIsOff=1
|
||
|
|
|
||
|
|
# Beacon filtering frequency (unit in beacon intervals)
|
||
|
|
gNthBeaconFilter=50
|
||
|
|
|
||
|
|
# Enable WAPI or not
|
||
|
|
WAPIIsEnabled=0
|
||
|
|
# Flags to filter Mcast abd Bcast RX packets.
|
||
|
|
# Value 0: No filtering, 1: Filter all Multicast.
|
||
|
|
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
|
||
|
|
McastBcastFilter=3
|
||
|
|
|
||
|
|
#Flag to enable HostARPOffload feature or not
|
||
|
|
hostArpOffload=0
|
||
|
|
|
||
|
|
#Flag to enable TCPChkSumOffld feature or not
|
||
|
|
gEnableTCPChkSumOffld=0
|
||
|
|
|
||
|
|
#Flag to enable HostNSOffload feature or not
|
||
|
|
hostNSOffload=1
|
||
|
|
gActiveModeOffload=1
|
||
|
|
|
||
|
|
#Flag to enable IPChkSumOffld feature or not
|
||
|
|
gEnableIPChecksumOffload=0
|
||
|
|
|
||
|
|
# 802.11n Protection flag
|
||
|
|
gEnableApProt=1
|
||
|
|
|
||
|
|
#Enable OBSS protection
|
||
|
|
gEnableApOBSSProt=1
|
||
|
|
|
||
|
|
# Fixed Rate
|
||
|
|
gFixedRate=0
|
||
|
|
|
||
|
|
# RTS threshold
|
||
|
|
RTSThreshold=192000
|
||
|
|
|
||
|
|
# Intra-BSS forward
|
||
|
|
gDisableIntraBssFwd=0
|
||
|
|
|
||
|
|
# WMM Enable/Disable
|
||
|
|
WmmIsEnabled=0
|
||
|
|
|
||
|
|
# 802.11d support
|
||
|
|
g11dSupportEnabled=1
|
||
|
|
|
||
|
|
# 802.11h support
|
||
|
|
g11hSupportEnabled=1
|
||
|
|
|
||
|
|
# ESE Support and fast transition
|
||
|
|
EseEnabled=0
|
||
|
|
ImplicitQosIsEnabled=0
|
||
|
|
gNeighborScanTimerPeriod=200
|
||
|
|
|
||
|
|
gNeighborLookupThreshold=76
|
||
|
|
gNeighborReassocThreshold=81
|
||
|
|
|
||
|
|
gNeighborScanChannelMinTime=20
|
||
|
|
gNeighborScanChannelMaxTime=30
|
||
|
|
gMaxNeighborReqTries=3
|
||
|
|
|
||
|
|
gEnableFastRoamInConcurrency=1
|
||
|
|
|
||
|
|
# CSR Roaming Enable(1) Disable(0)
|
||
|
|
gRoamingTime=0
|
||
|
|
|
||
|
|
# Roaming Preference
|
||
|
|
gRoamPrefer5GHz=1
|
||
|
|
gSelect5GHzMargin=20
|
||
|
|
|
||
|
|
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
|
||
|
|
# To enable, set FastRoamEnabled=1
|
||
|
|
# To disable, set FastRoamEnabled=0
|
||
|
|
FastRoamEnabled=1
|
||
|
|
|
||
|
|
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
|
||
|
|
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
|
||
|
|
#the RSSI of the new/roamable AP should be for roaming
|
||
|
|
RoamRssiDiff=3
|
||
|
|
|
||
|
|
# If the RSSI of any available candidate is better than currently associated
|
||
|
|
# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
|
||
|
|
# registering for reassoc threshold).
|
||
|
|
# NOTE: Value of 0 means that we would register for reassoc threshold.
|
||
|
|
gImmediateRoamRssiDiff=10
|
||
|
|
|
||
|
|
# To enable, set gRoamIntraBand=1 (Roaming within band)
|
||
|
|
# To disable, set gRoamIntraBand=0 (Roaming across band)
|
||
|
|
gRoamIntraBand=0
|
||
|
|
|
||
|
|
# SAP Country code
|
||
|
|
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
|
||
|
|
# Example
|
||
|
|
# US Indoor, USI
|
||
|
|
# Korea Outdoor, KRO
|
||
|
|
# Japan without optional byte, JP
|
||
|
|
# France without optional byte, FR
|
||
|
|
#gAPCntryCode=US
|
||
|
|
|
||
|
|
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
|
||
|
|
gAPAutoShutOff=0
|
||
|
|
|
||
|
|
# SAP auto channel selection configuration
|
||
|
|
# 0 = disable auto channel selection
|
||
|
|
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
|
||
|
|
gApAutoChannelSelection=0
|
||
|
|
|
||
|
|
#Preferred band (both or 2.4 only or 5 only)
|
||
|
|
BandCapability=0
|
||
|
|
|
||
|
|
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
|
||
|
|
enableBeaconEarlyTermination=0
|
||
|
|
beaconEarlyTerminationWakeInterval=3
|
||
|
|
|
||
|
|
#SOFTAP Channel Range selection
|
||
|
|
gAPChannelSelectStartChannel=1
|
||
|
|
gAPChannelSelectEndChannel=11
|
||
|
|
|
||
|
|
#SOFTAP Channel Range selection Operating band
|
||
|
|
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
|
||
|
|
gAPChannelSelectOperatingBand=0
|
||
|
|
|
||
|
|
# Listen Energy Detect Mode Configuration
|
||
|
|
# Valid values 0-128
|
||
|
|
# 128 means disable Energy Detect feature
|
||
|
|
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
|
||
|
|
# 10-128 are reserved.
|
||
|
|
# The EDET threshold mapping is as follows in 3dB step:
|
||
|
|
# 0 = -60 dBm
|
||
|
|
# 1 = -63 dBm
|
||
|
|
# 2 = -66 dBm
|
||
|
|
# ...
|
||
|
|
# 7 = -81 dBm
|
||
|
|
# 8 = -84 dBm
|
||
|
|
# 9 = -87 dBm
|
||
|
|
|
||
|
|
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
|
||
|
|
|
||
|
|
#
|
||
|
|
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
|
||
|
|
#
|
||
|
|
gEnablePhyAgcListenMode=128
|
||
|
|
|
||
|
|
#Enable Keep alive with non-zero period value
|
||
|
|
gStaKeepAlivePeriod = 30
|
||
|
|
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
|
||
|
|
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
|
||
|
|
#For both active and power save clients.
|
||
|
|
|
||
|
|
#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
|
||
|
|
#If doesn't honor for 5 seconds then DUT remove client.
|
||
|
|
|
||
|
|
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
|
||
|
|
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
|
||
|
|
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
|
||
|
|
|
||
|
|
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
|
||
|
|
#where we send NULL frame.
|
||
|
|
gApLinkMonitorPeriod = 10
|
||
|
|
gGoLinkMonitorPeriod = 10
|
||
|
|
|
||
|
|
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
|
||
|
|
#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
|
||
|
|
gGoKeepAlivePeriod = 20
|
||
|
|
gApKeepAlivePeriod = 20
|
||
|
|
|
||
|
|
#If set will start with active scan after driver load, otherwise will start with
|
||
|
|
#passive scan to find out the domain
|
||
|
|
gEnableBypass11d=1
|
||
|
|
|
||
|
|
#If set to 0, will not scan DFS channels
|
||
|
|
gEnableDFSChnlScan=1
|
||
|
|
|
||
|
|
# Enable Automatic Tx Power control
|
||
|
|
gEnableAutomaticTxPowerControl=1
|
||
|
|
|
||
|
|
# 0 for OLPC 1 for CLPC and SCPC
|
||
|
|
gEnableCloseLoop=1
|
||
|
|
|
||
|
|
# Scan Timing Parameters
|
||
|
|
gPassiveMaxChannelTime=110
|
||
|
|
gPassiveMinChannelTime=60
|
||
|
|
gActiveMaxChannelTime=40
|
||
|
|
gActiveMinChannelTime=20
|
||
|
|
|
||
|
|
# Enable Active mode offload
|
||
|
|
gEnableActiveModeOffload=1
|
||
|
|
|
||
|
|
#Enable Scan Results Aging based on timer
|
||
|
|
#Timer value is in seconds
|
||
|
|
#If Set to 0 it will not enable the feature
|
||
|
|
gScanAgingTime=0
|
||
|
|
|
||
|
|
#Enable Power saving mechanism Based on Android Framework
|
||
|
|
#If set to 0 Driver internally control the Power saving mechanism
|
||
|
|
#If set to 1 Android Framwrok control the Power saving mechanism
|
||
|
|
isAndroidPsEn=0
|
||
|
|
|
||
|
|
#disable LDPC in STA mode if the AP is TXBF capable
|
||
|
|
gDisableLDPCWithTxbfAP=0
|
||
|
|
|
||
|
|
#Enable thermal mitigation
|
||
|
|
gThermalMitigationEnable=1
|
||
|
|
gThermalTempMinLevel1=90
|
||
|
|
gThermalTempMaxLevel0=110
|
||
|
|
gThermalTempMaxLevel1=115
|
||
|
|
gThrottlePeriod=100
|
||
|
|
|
||
|
|
#List of Country codes for which 11ac needs to be disabled
|
||
|
|
#Each country code must be delimited by comma(,)
|
||
|
|
gListOfNon11acCountryCode=RU,UA,ZA
|
||
|
|
|
||
|
|
#Maxium Channel time in msec
|
||
|
|
gMaxMediumTime = 6000
|
||
|
|
|
||
|
|
#FlexConnect Power Factor
|
||
|
|
#Default is set to 0 (disable)
|
||
|
|
gFlexConnectPowerFactor=0
|
||
|
|
|
||
|
|
#Disable split scan, the FW will take care of it
|
||
|
|
gNumChanCombinedConc=60
|
||
|
|
|
||
|
|
#Enable Power Save offload
|
||
|
|
gEnablePowerSaveOffload=1
|
||
|
|
|
||
|
|
gEnableWoW=1
|
||
|
|
|
||
|
|
#Enable or Disable p2p device address administered
|
||
|
|
isP2pDeviceAddrAdministrated=0
|
||
|
|
|
||
|
|
#Disable scan_pno by default
|
||
|
|
gPNOScanSupport=0
|
||
|
|
|
||
|
|
#Enable TDLS
|
||
|
|
gEnableTDLSSupport=1
|
||
|
|
|
||
|
|
# Regulatory Setting; 0=STRICT; 1=CUSTOM
|
||
|
|
gRegulatoryChangeCountry=1
|
||
|
|
|
||
|
|
# Enable or Disable Rx thread
|
||
|
|
# 1=Enable (default), 0=Disable
|
||
|
|
gEnableRxThread=0
|
||
|
|
|
||
|
|
# Enable or Disable FW self-recovery
|
||
|
|
# Currently, It's for USB only.
|
||
|
|
# 1=Enable, 0=Disable (default)
|
||
|
|
gEnableFwSelfRecovery=0
|
||
|
|
gEnableSelfRecovery=0
|
||
|
|
gEnableForceTargetAssert=0
|
||
|
|
# Enable or Disable SAP suspend
|
||
|
|
# 1=Enable (default), 0=Disable
|
||
|
|
gEnableSapSuspend=0
|
||
|
|
|
||
|
|
# Enable TxBF
|
||
|
|
gTxBFEnable=1
|
||
|
|
|
||
|
|
# Enable or Disable WOW Pulse feature
|
||
|
|
# 1 = Enable, 0 = Disable (default)
|
||
|
|
gwow_pulse_support = 0
|
||
|
|
|
||
|
|
#P2P Listen offload
|
||
|
|
gEnableP2pListenOffload=1
|
||
|
|
|
||
|
|
# gEnableSAPAuthOffload: Enable Software AP Authentication Offload feature
|
||
|
|
# 1=Enable, 0=Disable (default)
|
||
|
|
gEnableSAPAuthOffload=0
|
||
|
|
|
||
|
|
# Sifs burst feature configuration
|
||
|
|
gEnableSifsBurst=1
|
||
|
|
gSoftApMaxPeers=32
|
||
|
|
|
||
|
|
gVhtMpduLen=2
|
||
|
|
# FW reorder
|
||
|
|
gReorderOffloadSupported=1
|
||
|
|
# DFS Master Capability
|
||
|
|
gEnableDFSMasterCap=1
|
||
|
|
|
||
|
|
#Fine tuned TxFlow parameters
|
||
|
|
TxFlowLowWaterMark=300
|
||
|
|
TxFlowHighWaterMarkOffset=94
|
||
|
|
|
||
|
|
# PTA
|
||
|
|
gCoexPtaConfigEnable=0
|
||
|
|
gCoexPtaConfigParam=0
|
||
|
|
gEnableNanSupport=0
|
||
|
|
|
||
|
|
#ETSI
|
||
|
|
gStaLocalEDCAForETSI=0
|
||
|
|
#TxBF in 20MHz
|
||
|
|
gEnableTxBFin20MHz=1
|
||
|
|
END
|
||
|
|
# Note: Configuration parser would not read anything past the END marker
|